You can prevent health problems from the start by limiting your exposure to hazardous materials. This means more than using respirators, goggles and protective clothing.
While the following guidelines are meant for an industrial setting, they can be an important guide for casual epoxy users. Consider the following steps to protect yourself from epoxy or any hazardous product.
Step 1 Make informed decisions about the products you use. Use the least hazardous product that will do the job. Often you can find a product with minimal health hazards that is adequate or even superior for the job. This can reduce or eliminate the hazard source.
Step 2 Set up a safe shop. Install equipment or use procedures that prevent or reduce exposure. This can include ventilation or specialized storage for hazardous materials. Effective ventilation can range from expensive, high-tech air-filtration and exhaust systems to the basic floor or window fans, and is useful for a wide range of vapours and dusts. A dedicated cabinet or isolated area for storing hazardous materials can help reduce exposure.
Step 3 Wear protective equipment (goggles, safety glasses, gloves, respirators, protective clothing, etc.) appropriate for the job at hand. The recommended minimum for most epoxy users is gloves, eye protection and protective clothing. Protect yourself from epoxy vapours by using a respirator with an organic vapor cartridge. The approved respiratory protection against epoxy dust, wood dust and nuisance dusts is a dust/mist mask or respirator.
Epoxy Resins and Hardeners
The government has not established exposure limits for WEST SYSTEM or PRO-SET epoxy products. We recommend limiting exposure to the levels approved for the raw materials used in formulating the product, as shown in the product’s MSDS. Practice the following procedures for the safe use and handling of our epoxy products.
Avoid contact with resin, hardeners, mixed epoxy and sanding dust from partially cured epoxy. Wear protective gloves and clothing whenever you handle epoxies. Barrier skin creams provide added protection. If you do get resin, hardener or mixed epoxy on your skin, remove it as soon as possible. Resin is not water-soluble, use a waterless skin cleanser to remove resin or mixed epoxy from your skin. Hardener is water soluble, wash with soap and warm water to remove hardener or sanding dust from your skin. Always wash thoroughly with soap and warm water after using epoxy, removing amine blush or sanding epoxy. If you spill epoxy on your clothes, change them immediately. Use skin cleanser to remove any epoxy from you and your clothes. If you cannot completely remove it from your clothes, do not continue to wear them. If it is mixed epoxy, you may wear the clothes again once the epoxy has completely cured. Never use solvents to remove epoxy from your skin.
Stop using the product if you develop a reaction. Resume work only after the symptoms disappear, usually after several days. When you resume work, improve your safety precautions to prevent exposure to epoxy, its vapours and sanding dust. If problems persist, discontinue use and consult a physician.
Protect your eyes from contact with resin, hardeners, mixed epoxy, and sanding dust by wearing appropriate eye protection. If epoxy gets in your eyes, immediately flush them with water under low pressure for 15 minutes. If discomfort persists, seek medical attention.
Avoid breathing concentrated vapors and sanding dust. All of our epoxies have a low volatile organic content (VOC), but vapors can build up in unvented spaces. Provide ample ventilation when working with epoxy in confined spaces, such as boat interiors. When you can’t adequately ventilate your workspace, wear an approved respirator with an organic vapour cartridge.
Provide ventilation and wear a dust/mist mask or respirator when sanding epoxy, especially partially cured epoxy. Breathing partially cured epoxy dust increases your risk of sensitization. Although epoxy cures quickly to a sandable solid, it may take over two weeks at room temperature, or elevated-temperature post-curing, to cure completely.
Avoid ingesting epoxy. Wash thoroughly after handling epoxy, especially before eating or smoking. If you swallow epoxy, drink large quantities of water, DO NOT induce vomiting. Hardeners are corrosive and can cause additional harm if vomited. Call a physician immediately. Refer to First Aid procedures on the Material Safety Data Sheet.
Keep your workshop clean to avoid incidental contact. Avoid touching door handles, light switches and containers when you have epoxy residue on your gloves, because you may touch them later without gloves on. Clean up spills with a scraper, collecting as much material as possible. Follow up with absorbent towels. Use sand, clay or other inert absorbent material to contain large spills. DO NOT use sawdust or other fine cellulose materials to absorb hardeners. Clean resin or mixed epoxy residue with acetone, lacquer thinner, or alcohol. Follow all safety warnings on solvent containers. Clean hardener residue with warm soapy water. You may reclaim uncontaminated resin or hardener for use. DO NOT dispose of hardener in trash containing sawdust or other fine cellulose materials, they can spontaneously combust.
Safely dispose of resin, hardener and empty containers. Puncture a corner of the can and drain residue into the appropriate new container of resin or hardener. Do not dispose of resin or hardener as liquids. Mix and cure waste resin and hardener (in small quantities) to make a non-hazardous inert solid. CAUTION! Pots of curing epoxy can get hot enough to ignite surrounding combustible materials and give off hazardous fumes. Place pots of mixed epoxy in a safe and ventilated area, away from workers and combustible materials. Dispose of the solid mass only after it has completely cured and cooled. Follow federal, state or local disposal regulations.